datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

HCPL-0211-560E View Datasheet(PDF) - Avago Technologies

Part Name
Description
View to exact match
HCPL-0211-560E Datasheet PDF : 18 Pages
First Prev 11 12 13 14 15 16 17 18
Package Characteristics
Parameter
Sym. Min. Typ. Max. Units     Test Conditions
Fig. Note
Input-Output Momentary
VISO
Withstand
Voltage*
HCNW22XX
3750 V rms RH < 50%, t = 1 min.
5000 TA = 25°C
5, 10
5, 11
Input-Output Resistance
RI-O
1012
Ω
VI-O = 500 Vdc
5
HCNW22XX
1012 1013
TA = 25°C
1011 TA = 100°C
Input-Output Capacitance
CI-O
0.6
pF
f = 1 MHz,
5
HCNW22XX
0.5 0.6 TA = 25°C, VI-O = 0 Vdc
Input-Input Insulation
II-I 0.005
µA Relative Humidity = 45%,
12
Leakage Current t = 5 s, VI-I = 500 V
Resistance (Input-Input)
RI-I
1011
Ω VI-I = 500 V
12
Capacitance (Input-Input)
CI-I
0.25
pF f = 1 MHz
12
*The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage
rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equipment level
safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203
Notes:
  1. Each channel.
  2. Derate total package power dissipation, PT, linearly above 70°C free-air temperature at a rate of 4.5 mW/°C.
  3. Duration of output short circuit time should not exceed 10 ms.
  4. For single devices, input capacitance is measured between pin 2 and pin 3.
  5. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together and pins 5, 6, 7, and 8 shorted together.
  6. The tPLH propagation delay is measured from the 50% point on the leading edge of the input pulse to the 1.3 V point on the leading edge of
the output pulse. The tPHL propagation delay is measured from the 50% point on the trailing edge of the input pulse to the 1.3 V point on the
trailing edge of the output pulse.
  7. CMH is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic high state, VO > 2.0 V.
CML is the maximum slew rate of the common mode voltage that can be sustained with the output voltage in the logic low state, VO < 0.8 V.
  8. For HCPL-2202/12, VO is on pin 6.
  9. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 is recommended.
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥4500 V rms for one second (leakage
detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table, if applicable.
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥6000 V rms for one second (leakage
detection current limit, II-O ≤5 µA). This test is performed before the 100% production test for partial discharge (Method b) shown in the IEC/
EN/DIN EN 60747-5-2 Insulation Characteristics Table.
12. For HCPL-2231/32 only. Measured between pins 1 and 2, shorted together, and pins 3 and 4, shorted together.
13
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]