datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

HCPL-0500-000E View Datasheet(PDF) - Avago Technologies

Part NameHCPL-0500-000E AVAGO
Avago Technologies AVAGO
DescriptionSingle Channel, High Speed Optocouplers
HCPL-0500-000E Datasheet PDF : 17 Pages
First Prev 11 12 13 14 15 16 17
Package Characteristics
Over recommended temperature (TA = 0°C to 70°C) unless otherwise specified.
Parameter
Sym.
Device
Min. Typ.* Max. Units Test Conditions
Fig.
Input-Output
VISO
Momentary
8-Pin DIP
3750
V rms
SO-8
Withstand     Widebo dy    50 00
Voltage**
RH < 50%,
t = 1 min.,
TA = 25°C
8-Pin DIP
5000
(Option 020)
II-O
8-Pin DIP
1
µA
Input-Output
RI-O
8-Pin DIP
1012
Ω
Resistance
SO-8
Widebody
1012 1013
1011
Input-Output
CI-O
8-Pin DIP
0.6
pF
Capacitance
SO-8
45% RH, t = 5 s,
VI-O = 3 kVdc,
TA = 25°C
VI-O = 500 Vdc
TA = 25°C
TA = 100°C
f = 1 MHz
Widebody
0.5
0.6
Note
6, 14
6, 15
6, 12,
15
6, 16
6
6
*All typicals at TA = 25°C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable), your
equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number
5963-2203E.
Notes:
  1.  Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).
  2.  Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).
  3.  Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).
  4.  Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).
  5.  CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, IO, to the forward LED input current, IF, times 100.
  6.  Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
  7.  Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dVCM/dt on the leading edge of the common
mode pulse signal, VCM, to assure that the output will remain in a Logic High state (i.e., VO > 2.0 V). Common mode transient immunity in a
Logic Low level is the maximum tolerable (negative) dVCM/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the
output will remain in a Logic Low state (i.e., VO < 0.8 V).
  8.  The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
  9.  The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor.
10.  The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
11.  The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%.
12.  See Option 020 data sheet for more information.
13.  Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended.
14.  In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation
Related Characteristics Table if applicable.
15.  In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage
detection current limit, II-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation
Related Characteristics Table if applicable.
16.  This rating is equally validated by an equivalent ac proof test.
12
Direct download click here
 

Description
These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance. These single channel optocouplers are available in 8-Pin DIP, SO-8 and Widebody package configurations.

Features
• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP, SO-8, widebody packages
• Open collector output
• Safety approval
UL Recognized – 3750 Vrms for 1 minute (5000 Vrms for 1 minute for HCNW and Option 020 devices) per UL1577 CSA Approved
IEC/EN/DIN EN 60747-5-2 Approved
– VIORM = 560 V peak for SO8 devices
– VIORM = 630 V peak for DIP 300mil devices
– VIORM = 1414 V peak for DIP 400mil (widebody) devices
• Dual channel version available (253X/053X/0534)

Applications
• High voltage insulation
• Video signal isolation
• Line receivers
• Feedback element in switched mode power supplies
• High speed logic ground isolation
– TTL/TTL, TTL/CMOS, TTL/LSTTL
• Replaces pulse transformers
• Replaces slow phototransistor isolators
• Analog signal ground isolation

Share Link : AVAGO
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]