datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

G104V1-T01 View Datasheet(PDF) - AZ Displays

Part NameDescriptionManufacturer
G104V1-T01 TFT LCD Approval Specification AZ-Displays
AZ Displays AZ-Displays
G104V1-T01 Datasheet PDF : 26 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Doc. No.:
Issued Date : Aug.9.2006
Model No :G104V1-T01
Approval
3.2 BACKLIGHT UNIT
Parameter
Symbol
Min.
Lamp Input Voltage
VL
440
Lamp Current
IL
2.0
Lamp Turn On Voltage VS
-
-
Operating Frequency
FL
Lamp Life Time
LBL
Power Consumption
PL
45
50,000
-
Note (1) IL means the lamp current of one lamp.
Value
Typ.
490
5.5
-
-
-
-
5.39
Ta = 25 ± 2 ºC
Max.
540
6.0
770 (25oC)
960 (0oC)
80
-
-
Unit
Note
VRMS
mARMS
VRMS
VRMS
KHz
Hrs
W
(1), IL = (5.5) mA
(1)
(2)
(2)
(3)
(5)
(4), IL = 5.5 mA
Note (2) The voltage shown above should be applied to the lamp for more than 1 second after startup.
Otherwise the lamp may not be turned on.
Note (3) The lamp frequency may produce interference with horizontal synchronous frequency from the
display, and this may cause line flow on the display. In order to avoid interference, the lamp
frequency should be detached from the horizontal synchronous frequency and its harmonics as far
as possible.
Note (4) PL = IL ×VL ×2
Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition
Ta = 25 ±2 oC and IL = ( 5.5 ) mArms until one of the following events occurs:
(a) When the brightness becomes or lower than 50% of its original value.
(b) When the effective ignition length becomes or lower than 80% of its original value. (Effective
ignition length is defined as an area that has less than 70% brightness compared to the
brightness in the center point.)
Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the
inverter must have specifications for the modularized lamp. The performance of the Backlight,
such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for
the lamp. All the parameters of an inverter should be carefully designed to avoid producing too
much current leakage from high voltage output of the inverter. When designing or ordering the
inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the
inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module
should be operated in the same manners when it is installed in your instrument.
The output of the inverter must have symmetrical (negative and positive) voltage waveform and
symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter
which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may
produce interface with horizontal synchronous frequency and as a result this may cause beat on the
display. Therefore lamp frequency shall be as away possible from the horizontal synchronous
frequency and from its harmonics in order to prevent interference.
Requirements for a system inverter design, which is intended to have a better display performance, a
10 / 26
Version 2.1
Direct download click here
 

Share Link : AZ-Displays
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]