D200ED View Datasheet(PDF) - MicroPower Direct, LLC
Part Name
Description
View to exact match
D200ED Datasheet PDF : 2 Pages
| |||
Model Selection Guide
Model
Number
D201ED
D202ED
D203ED
D204ED
D211ED
D212ED
D213ED
D214ED
D221ED
D222ED
D223ED
D224ED
Input
Voltage (VDC)
Nominal Range
Current (mA) Voltage
Full-Load No-Load (VDC)
5
4.5 - 5.5 500
30
5.0
5
4.5 - 5.5 487
30
9.0
5
4.5 - 5.5 487
30
12.0
5
4.5 - 5.5 481
30
15.0
12 10.8 - 13.2 208
12
5.0
12 10.8 - 13.2 201
12
9.0
12 10.8 - 13.2 196
12
12.0
12 10.8 - 13.2 201
12
15.0
24 21.6 - 26.4 102
7
5.0
24 21.6 - 26.4 101
7
9.0
24 21.6 - 26.4 99
7
12.0
24 21.6 - 26.4 99
7
15.0
Output 1
Output 2
Current Current Voltage Current Current
(mA, Max) (mA, Min) (VDC) (mA, Max) (mA, Min)
200.0
20.0
5.0
200.0
20.0
112.0
12.0
9.0
112.0
12.0
83.0
9.0
12.0
83.0
9.0
67.0
7.0
15.0
67.0
7.0
200.0
20.0
5.0
200.0
20.0
112.0
12.0
9.0
112.0
12.0
83.0
9.0
12.0
83.0
9.0
67.0
7.0
15.0
67.0
7.0
200.0
20.0
5.0
200.0
20.0
112.0
12.0
9.0
112.0
12.0
83.0
9.0
12.0
83.0
9.0
67.0
7.0
15.0
67.0
7.0
Efficiency
(%, Typ)
80
82
82
83
80
83
85
83
81
82
84
84
Fuse Rating
Slow-Blow
(mA)
1,000
1,000
1,000
1,000
500
500
500
500
250
250
250
250
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external ceramic
capacitor (approx approx 1 µF to 10 µF) be placed from each output to
common.
3. These units should not be operated with a load under 10% of full load.
Operation at no-load may cause damage to the unit.
4. These converters are specified for operation without external components.
However, in some applications the addition of input/ouput capacitors will
enhance stability and reduce output ripple. Recommended capacitor values
are:
Vin
5 VDC
12 VDC
24 VDC
Input
Capacitor
4.7 µF
2.2 µF
1.0 µF
Vout
5 VDC
9 VDC
12 VDC
15 VDC
Output
Capacitor
4.7 µF
2.2 µF
1.0 µF
0.47 µF
Block Diagram
For applications requiring very low output noise levels, a simple LC filter
should be effective.
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Derating Curve
Mechanical Dimensions
Pin Connections
Pin Function
1
+Vin
2
-Vin
4
-Vout 1
5
+Vout 1
6
-Vout 2
7
+Vout 2
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.01 (±0.25)
• Pin 1 is marked by a “dot” or indentation on the side of the unit
MicroPower Direct
www.micropowerdirect.com
292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: sales@micropowerdirect.com
|
|
Share Link: 