datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

L7583C View Datasheet(PDF) - Agere -> LSI Corporation

Part Name
Description
View to exact match
L7583C
Agere
Agere -> LSI Corporation Agere
L7583C Datasheet PDF : 20 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
L7583A/B/C/D Line Card Access Switch
Data Sheet
February 2001
Handling Precautions
Although protection circuitry has been designed into this device, proper precautions should be taken to avoid expo-
sure to electrostatic discharge (ESD) during handling and mounting. Lucent Technologies Microelectronics Group
employs a human-body model (HBM) and a charged-device model (CDM) for ESD-susceptibility testing and pro-
tection design evaluation. ESD voltage thresholds are dependent on the circuit parameters used to define the
model. No industry-wide standard has been adopted for CDM. However, a standard HBM (resistance = 1500 ,
capacitance = 100 pF) is widely used and therefore can be used for comparison purposes. The HBM ESD thresh-
old presented here was obtained by using these circuit parameters.
Table 3. HBM ESD Threshold Voltage
Device
L7583
Rating
1000 V
Electrical Characteristics
TA = –40 °C to +85 °C, unless otherwise specified.
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are
the result of engineering evaluations. Typical values are for information purposes only and are not part of the test-
ing requirements.
Table 4. Power Supply Specifications
Supply
VDD
Min
Typ
Max
4.5
5
5.5
Unit
Supply
V
VBAT*
Min
Typ
Max
Unit
–19
–72
V
* VBAT is used only as a reference for internal protection circuitry. If VBAT rises above –10 V, the device will enter an all OFF state and remain in
this state until the battery voltage drops below –15 V.
Table 5. Test In Switches, 1 and 2
Parameter
Test Condition
OFF-state Leakage Current:
+25 °C
Vswitch (differential) = –320 V to Gnd
Vswitch (differential) = –60 V to +260 V
+85 °C
Vswitch (differential) = –330 V to Gnd
Vswitch (differential) = –60 V to +270 V
–40 °C
Vswitch (differential) = –310 V to Gnd
Vswitch (differential) = –60 V to +250 V
ON-resistance:
+25 °C
Iswitch (on) = ±5 mA, ±10 mA
+85 °C
Iswitch (on) = ±5 mA, ±10 mA
–40 °C
Iswitch (on) = ±5 mA, ±10 mA
Isolation:
+25 °C
Vswitch (both poles) = ±320 V,
Logic inputs = Gnd
+85 °C
Vswitch (both poles) = ±330 V,
Logic inputs = Gnd
–40 °C
Vswitch (both poles) = ±310 V,
Logic inputs = Gnd
dV/dt Sensitivity*
Measure
Iswitch
Iswitch
Iswitch
VON
VON
VON
Iswitch
Iswitch
Iswitch
Min Typ Max Unit
— — 1 µA
— — 1 µA
— — 1 µA
— 45 —
— — 70
— 33 —
— — 1 µA
— — 1 µA
— — 1 µA
— 200 — V/µs
* Applied voltage is 100 Vp-p square wave at 100 Hz.
4
Lucent Technologies Inc.
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]