datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

LC33832M View Datasheet(PDF) - SANYO -> Panasonic

Part Name
Description
View to exact match
LC33832M
SANYO
SANYO -> Panasonic SANYO
LC33832M Datasheet PDF : 9 Pages
1 2 3 4 5 6 7 8 9
LC33832P, S, M, PL, SL, ML-70/80/10
Specifications
Absolute Maximum Ratings
Parameter
Symbol
Ratings
Unit Note
Maximum supply voltage
Input voltage
Output voltage
Allowable power dissipation
VCC max
VIN
VOUT
Pd max
–1.0 to +7.0
–1.0 to +7.0
–1.0 to +7.0
600
V1
V1
V1
mW 1
Output short-circuit current
Operating temperature
IOUT
Topr
50
0 to +70
mA 1
°C 1
Storage temperature
Tstg
–55 to +150
°C 1
Note: 1) Stresses greater than the above listed maximum values may result in damage to the device.
DC Recommended Operating Ranges at Ta = 0 to +70°C
Parameter
Symbol
min
typ
max
Unit
Note
Supply voltage
VCC
4.5
5.0
5.5
V
2
Input high level voltage
VIH
2.4
6.5
V
2
Input low level voltage
VIL
–1.0
+0.8
V
2
Note: 2) All voltages are referenced to GND.
DC Electrical Characteristics at Ta = 0 to +70°C, VCC = 5V±10%
Parameter
Symbol
Conditions
min max Unit Note
70ns
65
Operating current
ICCA Average current during operation
Access 80ns
time
100ns
60 mA 3,4
50
Standby current 1
Standby current 2
ICCS1 CE = OE/RFSH = VIH
ICCS2 CE = OE/RFSH = VCC –0.2V
LC33832P, S, M
LC33832PL, SL, ML
1 mA
1 mA
100 µA
Self-refresh current
LC33832P, S, M
ICCSR CE = VCC–0.2V, OE/RFSH = 0.2V LC33832PL, SL, ML
1 mA
100 µA
Input leakage current
IIL 0VVINVCC, pins other than test pin = 0V
–10 +10 µA
Output leakage current
IOL DOUT disable, 0VVOUTVCC
–10 +10 µA
Output high level voltage VOH IOUT = –5mA
2.4
V
Output low level voltage VOL IOUT = 4.2mA
0.4 V
Note: 3) All current values are measured at minimal cycle rate. Since current flows immoderately, cycle times may become longer
and shorter than shown here.
4) Dependent on output load. Maximum value is value during free state.
Input/Output Capacitance Characteristics at Ta = 25°C, f = 1MHz, VCC = 5V±10%
Parameter
Symbol
min
max
Unit
Input capacitance (A0 to A14)
CIN1
Input capacitance (CE, OE/RFSH, WE) CIN2
Input/output capacitance
CI/O
5
pF
7
pF
10
pF
Sampling inspections, and not full-lot inspections, are carried out for these parameters.
Test conditions
VIN1 = 0 V
VIN2 = 0 V
VI/O = 0 V
No. 4430-4/9
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]