datasheetbank_Logo     Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ADV7184BSTZ View Datasheet(PDF) - Analog Devices

Part NameDescriptionManufacturer
ADV7184BSTZ Multiformat SDTV Video Decoder with Fast Switch Overlay Support ADI
Analog Devices ADI
ADV7184BSTZ Datasheet PDF : 108 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ADV7184
TIMING SPECIFICATIONS
At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless
otherwise noted.
Table 3.
Parameter1,2
Symbol Test Conditions
SYSTEM CLOCK AND CRYSTAL
Nominal Frequency
Frequency Stability
I2C PORT3
SCLK Frequency
SCLK Min Pulse Width High
t1
SCLK Min Pulse Width Low
t2
Hold Time (Start Condition)
t3
Setup Time (Start Condition)
t4
SDA Setup Time
t5
SCLK and SDA Rise Time
t6
SCLK and SDA Fall Time
t7
Setup Time for Stop Condition t8
RESET FEATURE
Reset Pulse Width
CLOCK OUTPUTS
LLC1 Mark Space Ratio
t9:t10
LLC1 Rising to LLC2 Rising
t11
LLC1 Rising to LLC2 Falling
t12
DATA AND CONTROL OUTPUTS
Data Output Transitional Time4 t13
Data Output Transitional Time4 t14
Propagation Delay to Hi-Z
t15
Max Output Enable Access Time t16
Negative clock edge to start of valid data;
(tACCESS = t10 – t13)
End of valid data to negative clock edge;
(tHOLD = t9 + t14)
Min Output Enable Access Time t17
1 Temperature range TMIN to TMAX, –40°C to +85°C. The min/max specifications are guaranteed over this range.
2 Guaranteed by characterization.
3 TTL input values are 0 V to 3 V, with rise/fall times 3 ns, measured between the 10% and 90% points.
4 Timing figures obtained using default drive strength value (0xD5) in register subaddress 0xF4.
Min
0.6
1.3
0.6
0.6
100
5
45:55
Typ
28.63636
0.6
1
1
6
7
4
Max
±50
400
300
300
55:45
3.6
2.4
Unit
MHz
ppm
kHz
μs
μs
μs
μs
ns
ns
ns
μs
ms
% duty cycle
ns
ns
ns
ns
ns
ns
ns
ANALOG SPECIFICATIONS
At AVDD = 3.15 V to 3.45 V, DVDD = 1.65 V to 2.0 V, DVDDIO = 3.0 V to 3.6 V, PVDD = 1.71 V to 1.89 V. Operating temperature range, unless
otherwise noted. Recommended analog input video signal range: 0.5 V to 1.6 V, typically 1 V p-p.
Table 4.
Parameter1,2
Symbol
Test Conditions
CLAMP CIRCUITRY
External Clamp Capacitor
Input Impedance3
Clamps switched off
Input impedance of Pin 40 (FB)
Large Clamp Source Current
Large Clamp Sink Current
Fine Clamp Source Current
Fine Clamp Sink Current
1 Temperature range TMIN to TMAX, –40°C to +85°C. The min/max specifications are guaranteed over this range.
2 Guaranteed by characterization.
3 Except Pin 40 (FB).
Min
Typ
Max
Unit
0.1
μF
10
20
0.75
mA
0.75
mA
17
μA
17
μA
Rev. 0 | Page 7 of 108
Direct download click here

 

Share Link : 

All Rights Reserved © datasheetbank.com 2014 - 2020 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]