ADV7180KST48Z View Datasheet(PDF) - Analog Devices

Part Name

Description

View to exact match

ADV7180KST48Z

10-Bit, 4× Oversampling SDTV Video Decoder

Analog Devices 

ADV7180

SYNC PROCESSING

The ADV7180 extracts syncs embedded in the analog input

video signal. There is currently no support for external HS/VS

inputs. The sync extraction is optimized to support imperfect

video sources, such as VCRs with head switches. The actual

algorithm used employs a coarse detection based on a threshold

crossing, followed by a more detailed detection using an adaptive

interpolation algorithm. The raw sync information is sent to a

line length measurement and prediction block. The output of

this is then used to drive the digital resampling section to

ensure that the ADV7180 outputs 720 active pixels per line.

The sync processing on the ADV7180 also includes the following

specialized postprocessing blocks that filter and condition the

raw sync information retrieved from the digitized analog video:

• VSYNC processor. This block provides extra filtering of the

detected VSYNCs to improve vertical lock.

• HSYNC processor. The HSYNC processor is designed to

filter incoming HSYNCs that have been corrupted by

noise, providing much improved performance for video

signals with a stable time base but poor SNR.

VBI DATA RECOVERY

The ADV7180 can retrieve the following information from the

input video:

• Wide screen signaling (WSS)

• Copy generation management system (CGMS)

• Closed captioning (CCAP)

• Macrovision protection presence

• EDTV data

• Gemstar-compatible data slicing

• Teletext

• VITC/VPS

The ADV7180 is also capable of automatically detecting the

incoming video standard with respect to

• Color subcarrier frequency

• Field rate

• Line rate

The ADV7180 can configure itself to support PAL B/D/I/G/H,

PAL M, PAL N, PAL Combination N, NTSC M, NTSC J,

SECAM 50 Hz/60 Hz, NTSC 4.43, and PAL 60.

Data Sheet

GENERAL SETUP

Video Standard Selection

The VID_SEL[3:0] bits (Address 0x00[7:4]) allow the user to

force the digital core into a specific video standard. Under

normal circumstances, this is not necessary. The VID_SEL[3:0]

bits default to an autodetection mode that supports PAL, NTSC,

SECAM, and variants thereof.

Autodetection of SD Modes

To guide the autodetect system of the ADV7180, individual

enable bits are provided for each of the supported video standards.

Setting the relevant bit to 0 inhibits the standard from being

detected automatically. Instead, the system chooses the closest of

the remaining enabled standards. The results of the autodetection

block can be read back via the status registers (see the Global

Status Register section for more information).

VID_SEL[3:0], Address 0x00[7:4]

Table 24. VID_SEL Function

VID_SEL[3:0] Description

0000 (default)

Autodetect (PAL B/G/H/I/D), NTSC J

(no pedestal), SECAM

0001

Autodetect (PAL B/G/H/I/D), NTSC M

(pedestal), SECAM

0010

Autodetect (PAL N) (pedestal), NTSC J

(no pedestal), SECAM

0011

Autodetect (PAL N) (pedestal), NTSC M

(pedestal), SECAM

0100

NTSC J

0101

NTSC M

0110

PAL 60

0111

NTSC 4.43

1000

PAL B/G/H/I/D

1001

PAL N = PAL B/G/H/I/D (with pedestal)

1010

PAL M (without pedestal)

1011

PAL M

1100

PAL Combination N

1101

PAL Combination N (with pedestal)

1110

SECAM

1111

SECAM (with pedestal)

AD_SEC525_EN, Enable Autodetection of SECAM 525

Line Video, Address 0x07[7]

Setting AD_SEC525_EN to 0 (default) disables the autodetection

of a 525-line system with a SECAM style, FM-modulated color

component.

Setting AD_SEC525_EN to 1 enables the detection of a SECAM

style, FM-modulated color component.

Rev. G | Page 26 of 120

Share Link: