datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ADV7178 View Datasheet(PDF) - Analog Devices

Part Name
Description
View to exact match
ADV7178 Datasheet PDF : 38 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
ADV7177/ADV7178
3.3 V SPECIFICATIONS (VAA = +3.0 V–3.6 V1, VREF = 1.235 V, RSET = 300 . All specifications TMIN to TMAX2 unless otherwise noted.)
Parameter
Conditions1
Min
Typ
Max
Units
STATIC PERFORMANCE3
Resolution (Each DAC)
Accuracy (Each DAC)
Integral Nonlinearity
Differential Nonlinearity
Guaranteed Monotonic
9
Bits
± 0.5
LSB
± 0.5
LSB
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN3, 4
Input Current, IIN3, 5
Input Capacitance, CIN
VIN = 0.4 V or 2.4 V
VIN = 0.4 V or 2.4 V
2
V
0.8
V
±1
µA
± 50
µA
10
pF
DIGITAL OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Three-State Leakage Current3
Three-State Output Capacitance3
ISOURCE = 400 µA
ISINK = 3.2 mA
2.4
V
0.4
V
10
µA
10
pF
ANALOG OUTPUTS3
Output Current6, 7
Output Current8
DAC-to-DAC Matching
Output Compliance, VOC
Output Impedance, ROUT
Output Capacitance, COUT
POWER REQUIREMENTS3, 9
VAA
Normal Power Mode
IDAC (max)10
IDAC (min)10
ICCT9
Low Power Mode
IDAC (max)10
IDAC (min)10
ICCT11
Power Supply Rejection Ratio
RSET = 300 , RL = 75
IOUT = 0 mA
RSET = 300 , RL = 150
COMP = 0.1 µF
16.5
17.35 18.5
mA
5
mA
2.0
%
0
+1.4
V
15
k
30
pF
3.0
3.3
3.6
V
113
116
mA
15
mA
45
mA
60
mA
25
mA
45
mA
0.01 0.5
%/%
NOTES
11The max/min specifications are guaranteed over this range. The max/min values are typical over 3.0 V to 3.6 V.
12Temperature range TMIN to TMAX: 0°C to +70°C.
13Guaranteed by characterization.
14All digital input pins except pins RESET, OSD0 and CLOCK.
15Excluding all digital input pins except pins RESET, OSD0 and CLOCK.
16Full drive into 75␣ load.
17DACs can output 35 mA typically at 3.3 V (RSET = 150 and RL = 75 ), optimum performance obtained at 18 mA DAC current (RSET = 300 and RL = 150 ).
18Minimum drive current (used with buffered/scaled output load).
19Power measurements are taken with Clock Frequency = 27 MHz. Max T J = 110°C.
10IDAC is the total current (min corresponds to 5 mA output per DAC, max corresponds to 38 mA output per DAC) to drive all three DACs. Turning off individual
DACs reduces IDAC correspondingly.
11ICCT (Circuit Current) is the continuous current required to drive the device.
Specifications subject to change without notice.
REV. 0
–3–
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]