ADV7173KST View Datasheet(PDF) - Analog Devices
Part Name
Description
View to exact match
ADV7173KST Datasheet PDF : 60 Pages
| |||
SPECIFICATIONS
ADV7172/ADV7173
5 V SPECIFICATIONS (VAA = 5 V ؎ 5%1, VREF = 1.235 V, RSET1,2 = 600 ⍀ unless otherwise noted. All specifications TMIN to TMAX2
unless otherwise noted.)
Parameter
Test Conditions1
Min
Typ
Max
Unit
STATIC PERFORMANCE
Resolution (Each DAC)
Accuracy (Each DAC)
Integral Nonlinearity3
Differential Nonlinearity3
Guaranteed Monotonic
10
Bits
± 1.0
LSB
± 1.0
LSB
DIGITAL INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN
DIGITAL OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Three-State Leakage Current
Three-State Output Capacitance
VIN = 0.4 V or 2.4 V
ISOURCE = 400 µA
ISINK = 3.2 mA
2
V
0.8
V
±1
µA
10
pF
2.4
V
0.4
V
10
µA
10
pF
ANALOG OUTPUTS
Output Current (DACs A, B, C)4
Output Current (DACs A, B, C)5
Output Current (DACs D, E, F)6
Output Current (DACs D, E, F)5
DAC-to-DAC Matching (DACs A, B, C)7
DAC-to-DAC Matching (DACs D, E, F)7
Output Compliance, VOC
Output Impedance, ROUT
Output Capacitance, COUT
VOLTAGE REFERENCE
Reference Range, VREF
POWER REQUIREMENTS
VAA
Normal Power Mode
IDAC (max)8, 9
IDAC (min)8, 9
ICCT10
Low Power Mode
IDAC (max)11
IDAC (min)11
ICCT10
Sleep Mode
IDAC12
ICCT13
Power Supply Rejection Ratio
RSET1 = 150 Ω, RL = 37.5 Ω
RSET1 = 1041 Ω, RL = 262.5 Ω
RSET2 = 600 Ω, RL = 150 Ω
RSET2 = 1041 Ω, RL = 262.5 Ω
IOUT = 0 mA
IVREFOUT = 20 µA
RSET1,2 = 600 Ω
RSET1,2 = 1041 Ω
RSET1 = 150 Ω
COMP = 0.1 µF
33
8.25
0
1.112
4.75
34.7 37
5
8.66 9.25
5
1
4.0
1
4.0
1.4
30
30
1.235 1.359
5.0
5.25
59
65
30
78
90
64
15
78
90
0.1
0.1
0.01 0.5
mA
mA
mA
mA
%
%
V
kΩ
pF
V
V
mA
mA
mA
mA
mA
mA
µA
µA
%/%
NOTES
1The max/min specifications are guaranteed over this range. The max/min values are typical over 4.75 V to 5.25 V.
2Temperature range TMIN to TMAX: 0°C to 70°C.
3Characterized by design.
4Full drive into 75 Ω doubly terminated load.
5Minimum drive current (used with buffered/scaled output load).
6Full drive into 150 Ω load.
7Specification guaranteed by characterization.
8IDAC is the total current (“min” corresponds to 5 mA output per DAC, “max” corresponds to 8.66 mA output per DAC ) to drive DACs A, B, C, D, E, F. Turning off
individual DACs reduces IDAC correspondingly, also DACs A, B, C can be configured to output a max current of 37 mA but DAC D, E, F must be turned off.
9All six DACs on (DAC A, B, C, D, E, F).
10ICCT (Circuit Current) is the continuous current required to drive the device.
11Only large DACs (DACs A, B, C) on per low power mode.
12Total DAC current in Sleep Mode.
13Total continuous current during Sleep Mode.
Specifications subject to change without notice.
REV. B
–3–
|
|
Share Link: 