datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

ADV7150L View Datasheet(PDF) - Analog Devices

Part NameDescriptionManufacturer
ADV7150L CMOS 220 MHz True-Color Graphics Triple 10-Bit Video RAM-DAC ADI
Analog Devices ADI
ADV7150L Datasheet PDF : 36 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
Mnemonic
R/W
C0, C1
IOR; IOR, IOG; IOG, IOB;
IOB
VREF
RSET
COMP
IPLL
VAA
GND
ADV7150
Function
Read/Write Control (TTL Compatible Input). This input determines whether data is
written to or read from the device’s registers and color palette RAM. R/W and CE must
be at Logic “0” to write data to the part. R/W must be at Logic “1” and CE at Logic
“0” to read from the device.
Command Controls (TTL Compatible Inputs). These inputs determine the type of read
or write operation being performed on the device over the databus (see Interface Truth
Table). Data on these inputs is latched on the falling edge of CE.
Red, Green and Blue Current Outputs (High Impedance Current Sources). These RGB
video outputs are specified to directly drive RS-343A and RS-170 video levels into dou-
bly terminated 75 loads.
IOR, IOG and IOB are the complementary outputs of IOR, IOG and IOB. These out-
puts can be tied to GND if it is not required to use differential outputs.
Voltage Reference Input (Analog Input). An external 1.235 V voltage reference is re-
quired to drive this input. An AD589 (2-terminal voltage reference) or equivalent is rec-
ommended. (Note: It is not recommended to use a resistor network to generate the
voltage reference.)
Output Full-Scale Adjust Control (Analog Input). A resistor connected between this pin
and analog ground controls the absolute amplitude of the output video signal. The value
of RSET is derived from the full-scale output current on IOG according to the following
equations:
RSET () = C1 × VREF/IOG (mA); SYNC on GREEN
RSET () = C2 × VREF/IOG (mA); NO SYNC on GREEN.
Full-Scale output currents on IOR and IOB for a particular value of RSET are given by:
IOR (mA)= C2 × VREF(V)/RSET ()
and
IOB (mA) = C2 × VREF (V)/RSET ()
where C1 = 6,050; PEDESTAL = 7.5 IRE
where C1 = 5,723; PEDESTAL = 0 IRE
and
where C2 = 4,323; PEDESTAL = 7.5 IRE
where C1 = 3,996; PEDESTAL = 0 IRE.
Compensation Pin. A 0.1 µF capacitor should be connected between this pin and VAA.
Phase Lock Loop Output Current (High Impedance Current Source). This output is
used to enable multiple ADV7150s along with ADV7151s to be synchronized together
with pixel resolution when using an external PLL. This output is triggered either from
the falling edge of SYNC or BLANK as determined by bit CR21 of Command Register
2. When activated, it supplies a current corresponding to:
IPLL (mA) = 1,728 × VREF(V)/RSET ()
When not using the IPLL function, this output pin should be tied to GND.
Power Supply (+5 V ± 5%). The part contains multiple power supply pins, all should be
connected together to one common +5 V filtered analog power supply.
Analog Ground. The part contains multiple ground pins, all should be connected
together to the system’s ground plane.
REV. A
–11–
Direct download click here
 

Share Link : ADI
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]