datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ADR291 View Datasheet(PDF) - Analog Devices

Part Name
Description
View to exact match
ADR291 Datasheet PDF : 20 Pages
First Prev 11 12 13 14 15 16 17 18 19 20
THEORY OF OPERATION
The ADR291/ADR292 series of references uses a reference
generation technique known as XFET (eXtra implanted junc-
tion FET). This technique yields a reference with low noise, low
supply current, and very low thermal hysteresis.
The core of the XFET reference consists of two junction field
effect transistors, one having an extra channel implant to raise
its pinch-off voltage. By running the two JFETs at the same
drain current, the difference in pinch-off voltage can be amplified
and used to form a highly stable voltage reference. The intrinsic
reference voltage is around 0.5 V with a negative temperature
coefficient of about −120 ppm/K. This slope is essentially
locked to the dielectric constant of silicon and can be closely
compensated by adding a correction term generated in the same
fashion as the proportional-to-temperature (PTAT) term used
to compensate band gap references. Because most of the noise
of a band gap reference comes from the compensation circuitry,
the intrinsic temperature coefficient offers a significant advan-
tage (being about 30 times lower), and therefore, requiring less
correction resulting in much lower noise.
The simplified schematic in Figure 31 shows the basic topology
of the ADR291/ADR292 series. The temperature correction
term is provided by a current source with a value designed to be
proportional to absolute temperature. The general equation is
VOUT
=
ΔVP
⎜⎛
R1
+
R2 +
R1
R3 ⎟⎞ +
(IPTAT ) (R3)
where:
ΔVP is the difference in pinch-off voltage between the two FETs.
IPTAT is the positive temperature coefficient correction current.
The various versions of the ADR291/ADR292 family are created
by on-chip adjustment of R1 and R3 to achieve 2.500 V or
4.096 V at the reference output.
The process used for the XFET reference also features vertical
NPN and PNP transistors, the latter of which are used as output
devices to provide a very low dropout voltage.
VIN
I1 I1
1
 VP
VOUT
R1
IPTAT
R2
R3
1 EXTRA CHANNEL IMPLANT
VOUT
=
R1
+
R2
R1
+
R3
×
ΔVP
=
IPTAT
×
R3
GND
Figure 31. ADR291/ADR292 Simplified Schematic
ADR291/ADR292
DEVICE POWER DISSIPATION CONSIDERATIONS
The ADR291/ADR292 family of references is guaranteed to
deliver load currents to 5 mA with an input voltage that ranges
from 2.7 V to 15 V (minimum supply voltage depends on the
output voltage chosen). When these devices are used in
applications with large input voltages, care should be exercised
to avoid exceeding the published specifications for maximum
power dissipation or junction temperature that could result in
premature device failure. Use the following formula to calculate
maximum junction temperature or dissipation of a device:
PD
=
TJ TA
θJA
where
TJ and TA are the junction and ambient temperatures,
respectively.
PD is the device power dissipation.
θJA is the device package thermal resistance.
BASIC VOLTAGE REFERENCE CONNECTIONS
References, in general, require a bypass capacitor connected
from the VOUT pin to the GND pin. The circuit in Figure 32
illustrates the basic configuration for the ADR291/ADR292
family of references. Note that the decoupling capacitors are not
required for circuit stability.
+
10µF
NC 1
2
NC 3
0.1µF
4
ADR291/
ADR292
8 NC
7 NC
VOUT
6
5 NC
0.1µF
NC = NO CONNECT
Figure 32. Basic Voltage Reference Configuration
NOISE PERFORMANCE
The noise generated by the ADR291/ADR292 family of refer-
ences is typically less than 12 μV p-p over the 0.1 Hz to 10 Hz
band. The noise measurement is made with a band-pass filter
made of a 2-pole high-pass filter with a corner frequency at 0.1 Hz
and a 2-pole low-pass filter with a corner frequency at 10 Hz.
TURN-ON TIME
Upon application of power (cold start), the time required for
the output voltage to reach its final value within a specified
error band is defined as the turn-on settling time. Two com-
ponents normally associated with this are the time it takes for
the active circuits to settle and for the thermal gradients on the
chip to stabilize. Figure 28 shows the turn-on settling time for
the ADR291.
Rev. F | Page 13 of 20
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]