datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

ADP121CB-2.5-EVALZ View Datasheet(PDF) - Analog Devices

Part NameADP121CB-2.5-EVALZ ADI
Analog Devices ADI
Description150 mA, Low Quiescent Current, CMOS Linear Regulator
ADP121CB-2.5-EVALZ Datasheet PDF : 20 Pages
First Prev 11 12 13 14 15 16 17 18 19 20
ADP121
APPLICATIONS INFORMATION
CAPACITOR SELECTION
Output Capacitor
The ADP121 is designed for operation with small, space-saving
ceramic capacitors, but functions with most commonly used
capacitors as long as care is taken with the effective series resistance
(ESR) value. The ESR of the output capacitor affects stability of the
LDO control loop. A minimum of 0.70 µF capacitance with an
ESR of 1 Ω or less is recommended to ensure stability of the
ADP121. The transient response to changes in the load current is
also affected by output capacitance. Using a larger value of output
capacitance improves the transient response of the ADP121 to
large changes in the load current. Figure 28 and Figure 29 show
the transient responses for output capacitance values of 1 µF and
4.7 µF, respectively.
ILOAD
1mA TO 150mA LOAD STEP,
2.5A/µs
CH1 MEAN
115.7mA
VOUT = 1.8V,
CIN = COUT = 1µF
VOUT
(400ns/DIV)
Figure 28. Output Transient Response, COUT = 1 µF
ILOAD
1mA TO 150mA LOAD STEP,
2.5A/µs
VOUT
VOUT = 1.8V,
CIN = COUT = 4.7µF
(400ns/DIV)
Figure 29. Output Transient Response, COUT = 4.7 µF
Data Sheet
Input Bypass Capacitor
Connecting a 1 µF capacitor from VIN to GND reduces the
circuit sensitivity to the PCB layout, especially when long input
traces or high source impedance is encountered. If output
capacitance greater than 1 µF is required, the input capacitor
should be increased to match it.
Input and Output Capacitor Properties
Any good quality ceramic capacitor can be used with the
ADP121, as long as it meets the minimum capacitance and
maximum ESR requirements. Ceramic capacitors are manufac-
tured with a variety of dielectrics, each with a different behavior
over temperature and applied voltage. Capacitors must have an
adequate dielectric to ensure the minimum capacitance over
the necessary temperature range and dc bias conditions. X5R
or X7R dielectrics with a voltage rating of 6.3 V or 10 V are
recomm ended. Y5V and Z5U dielectrics are not
recommended, due to their poor temperature and dc bias
characteristics.
Figure 30 depicts the capacitance vs. voltage bias characteristic
of an 0402 1 µF, 10 V, X5R capacitor. The voltage stability of a
capacitor is strongly influenced by the capacitor size and voltage
rating. In general, a capacitor in a larger package or higher voltage
rating exhibits better stability. The temperature variation of the
X5R dielectric is about ±15% over the −40°C to +85°C tempera-
ture range and is not a function of package or voltage rating.
1.2
1.0
0.8
0.6
0.4
0.2
0
0
2
4
6
8
10
VOLTAGE (V)
Figure 30. Capacitance vs. Voltage Bias Characteristic
Rev. G | Page 12 of 20
Direct download click here

GENERAL DESCRIPTION
The ADP121 is a quiescent current, low dropout, linear regulator that operates from 2.3 V to 5.5 V and provides up to 150 mA of output current. The low 135 mV dropout voltage at 150 mA load improves efficiency and allows operation over a wide input voltage range. The low 30 μA of quiescent current at full load makes the ADP121 ideal for battery-operated portable equipment.
The ADP121 is available in output voltages ranging from 1.2 V to 3.3 V. The parts are optimized for stable operation with small 1 μF ceramic output capacitors. The ADP121 delivers good transient performance with minimal board area.
Short-circuit protection and thermal overload protection circuits prevent damage in adverse conditions. The ADP121 is available in a tiny 5-lead TSOT and 4-ball 0.4 mm pitch halide-free WLCSP packages and utilizes the smallest footprint solution to meet a variety of portable applications.

FEATURES
  Input voltage range: 2.3 V to 5.5 V
  Output voltage range: 1.2 V to 3.3 V
  Output current: 150 mA
  Low quiescent current
     IGND = 11 μA with 0 μA load
     IGND = 30 μA with 150 mA load
  Low shutdown current: <1 μA
  Low dropout voltage
     90 mV @ 150 mA load
  High PSRR
     70 dB @ 1 kHz at VOUT = 1.2 V
     70 dB @ 10 kHz at VOUT = 1.2 V
  Low noise: 40 μV rms at VOUT = 1.2 V
  No noise bypass capacitor required
  Output voltage accuracy: ±1%
  Stable with a small 1 μF ceramic output capacitor
  Current limit and thermal overload protection
  Logic controlled enable
  5-lead TSOT package
  4-ball 0.4 mm pitch WLCSP
 
APPLICATIONS
  Mobile phones
  Digital cameras and audio devices
  Portable and battery-powered equipment
  Post dc-to-dc regulation
  Post regulation

Share Link : ADI
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]