datasheetbank_Logo     Технический паспорт Поисковая и бесплатно техническое описание Скачать

ADC08200CIMT Просмотр технического описания (PDF) - National ->Texas Instruments

Номер в каталогеКомпоненты Описаниепроизводитель
ADC08200CIMT 8-Bit, 20 Msps to 200 Msps, Low Power A/D Converter with Internal Sample-and-Hold National-Semiconductor
National ->Texas Instruments National-Semiconductor
ADC08200CIMT Datasheet PDF : 20 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Specification Definitions
APERTURE (SAMPLING) DELAY is that time required after
the rise of the clock input for the sampling switch to open. The
Sample/Hold circuit effectively stops capturing the input sig-
nal and goes into the “hold” mode tAD after the clock goes
high.
APERTURE JITTER is the variation in aperture delay from
sample to sample. Aperture jitter shows up as input noise.
CLOCK DUTY CYCLE is the ratio of the time that the clock
wave form is at a logic high to the total time of one clock pe-
riod.
DIFFERENTIAL NON-LINEARITY (DNL) is the measure of
the maximum deviation from the ideal step size of 1 LSB.
Measured at 200 Msps with a ramp input.
EFFECTIVE NUMBER OF BITS (ENOB, or EFFECTIVE
BITS) is another method of specifying Signal-to-Noise and
Distortion Ratio, or SINAD. ENOB is defined as (SINAD –
1.76) / 6.02 and says that the converter is equivalent to a per-
fect ADC of this (ENOB) number of bits.
FULL POWER BANDWIDTH is a measure of the frequency
at which the reconstructed output fundamental drops 3 dB
below its low frequency value for a full scale input.
FULL-SCALE ERROR is a measure of how far the last code
transition is from the ideal 1½ LSB below VRT and is defined
as:
Vmax + 1.5 LSB – VRT
where Vmax is the voltage at which the transition to the maxi-
mum (full scale) code occurs.
INTEGRAL NON-LINEARITY (INL) is a measure of the de-
viation of each individual code from a line drawn from zero
scale (½ LSB below the first code transition) through positive
full scale (½ LSB above the last code transition). The devia-
tion of any given code from this straight line is measured from
the center of that code value. The end point test method is
used. Measured at 200 Msps with a ramp input.
INTERMODULATION DISTORTION (IMD) is the creation of
additional spectral components as a result of two sinusoidal
frequencies being applied to the ADC input at the same time.
it is defined as the ratio of the power in the second and third
order intermodulation products to the power in one of the
original frequencies. IMD is usually expressed in dBFS.
MISSING CODES are those output codes that are skipped
and will never appear at the ADC outputs. These codes can-
not be reached with any input value.
OUTPUT DELAY is the time delay after the rising edge of the
input clock before the data update is present at the output
pins.
OUTPUT HOLD TIME is the length of time that the output data
is valid after the rise of the input clock.
PIPELINE DELAY (LATENCY) is the number of clock cycles
between initiation of conversion and when that data is pre-
sented to the output driver stage. New data is available at
every clock cycle, but the data lags the conversion by the
Pipeline Delay plus the Output Delay.
POWER SUPPLY REJECTION RATIO (PSRR) is a measure
of how well the ADC rejects a change in the power supply
voltage. For the ADC08200, PSRR1 is the ratio of the change
in Full-Scale Error that results from a change in the DC power
supply voltage, expressed in dB. PSRR2 is a measure of how
well an AC signal riding upon the power supply is rejected
from the output and is here defined as
where SNR0 is the SNR measured with no noise or signal on
the supply line and SNR1 is the SNR measured with a
1 MHz, 200 mVP-P signal riding upon the supply lines.
SIGNAL TO NOISE RATIO (SNR) is the ratio, expressed in
dB, of the rms value of the input signal at the output to the rms
value of the sum of all other spectral components below one-
half the sampling frequency, not including harmonics or d.c.
SIGNAL TO NOISE PLUS DISTORTION (S/(N+D) or
SINAD) is the ratio, expressed in dB, of the rms value of the
input signal at the output to the rms value of all of the other
spectral components below half the clock frequency, includ-
ing harmonics but excluding d.c.
SPURIOUS FREE DYNAMIC RANGE (SFDR) is the differ-
ence, expressed in dB, between the rms values of the input
signal at the output and the peak spurious signal, where a
spurious signal is any signal present in the output spectrum
that is not present at the input.
TOTAL HARMONIC DISTORTION (THD) is the ratio ex-
pressed in dB, of the rms total of the first nine harmonic levels
at the output to the level of the fundamental at the output. THD
is calculated as
where Af1 is the RMS power of the fundamental (output) fre-
quency and Af2 through Af10 are the RMS power of the first 9
harmonic frequencies in the output spectrum
ZERO SCALE OFFSET ERROR is the error in the input volt-
age required to cause the first code transition. It is defined as
VOFF = VZT − VRB
where VZT is the first code transition input voltage.
www.national.com
8
Direct download click here

 

Share Link : 

All Rights Reserved © datasheetbank.com 2014 - 2019 [ политика конфиденциальности ] [ Запрос Даташит ]