datasheetbank_Logo   Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :   

ADC0809 View Datasheet(PDF) - National ->Texas Instruments

Part NameDescriptionManufacturer
ADC0809 8-Bit µP Compatible A/D Converters with 8-Channel Multiplexer National-Semiconductor
National ->Texas Instruments National-Semiconductor
ADC0809 Datasheet PDF : 14 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
Electrical Characteristics (Continued)
Digital Levels and DC Specifications: ADC0808CCN, ADC0808CCV, ADC0809CCN and ADC0809CCV, 4.75VCC5.25V,
−40˚CTA+85˚C unless otherwise noted
Symbol
Parameter
Conditions
Min
Typ
Max
Units
DATA OUTPUTS AND EOC (INTERRUPT)
VOUT(1)
VOUT(0)
VOUT(0)
IOUT
Logical “1” Output Voltage
Logical “0” Output Voltage
Logical “0” Output Voltage EOC
TRI-STATE Output Current
VCC = 4.75V
IOUT = −360µA
IOUT = −10µA
IO=1.6 mA
IO=1.2 mA
VO=5V
VO=0
2.4
V(min)
4.5
V(min)
0.45
V
0.45
V
3
µA
−3
µA
Electrical Characteristics
Timing Specifications VCC=VREF(+)=5V, VREF(−)=GND, tr=tf=20 ns and TA=25˚C unless otherwise noted.
Symbol
Parameter
Conditions
MIn Typ
Max
tWS
tWALE
ts
tH
tD
Minimum Start Pulse Width
Minimum ALE Pulse Width
Minimum Address Set-Up Time
Minimum Address Hold Time
Analog MUX Delay Time
From ALE
(Figure 5)
(Figure 5)
(Figure 5)
(Figure 5)
RS=0(Figure 5)
100
200
100
200
25
50
25
50
1
2.5
tH1, tH0
t1H, t0H
tc
fc
tEOC
OE Control to Q Logic State
OE Control to Hi-Z
Conversion Time
Clock Frequency
EOC Delay Time
CL=50 pF, RL=10k (Figure 8)
CL=10 pF, RL=10k (Figure 8)
fc=640 kHz, (Figure 5) (Note 7)
(Figure 5)
125
250
125
250
90 100
116
10 640
1280
0
8+2 µS
CIN
COUT
Input Capacitance
TRI-STATE Output
Capacitance
At Control Inputs
At TRI-STATE Outputs
10
15
10
15
Units
ns
ns
ns
ns
µs
ns
ns
µs
kHz
Clock
Periods
pF
pF
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications do not apply when operating
the device beyond its specified operating conditions.
Note 2: All voltages are measured with respect to GND, unless othewise specified.
Note 3: A zener diode exists, internally, from VCC to GND and has a typical breakdown voltage of 7 VDC.
Note 4: Two on-chip diodes are tied to each analog input which will forward conduct for analog input voltages one diode drop below ground or one diode drop greater
than the VCCn supply. The spec allows 100 mV forward bias of either diode. This means that as long as the analog VIN does not exceed the supply voltage by more
than 100 mV, the output code will be correct. To achieve an absolute 0VDC to 5VDC input voltage range will therefore require a minimum supply voltage of 4.900 VDC
over temperature variations, initial tolerance and loading.
Note 5: Total unadjusted error includes offset, full-scale, linearity, and multiplexer errors. See Figure 3. None of these A/Ds requires a zero or full-scale adjust. How-
ever, if an all zero code is desired for an analog input other than 0.0V, or if a narrow full-scale span exists (for example: 0.5V to 4.5V full-scale) the reference voltages
can be adjusted to achieve this. See Figure 13.
Note 6: Comparator input current is a bias current into or out of the chopper stabilized comparator. The bias current varies directly with clock frequency and has little
temperature dependence (Figure 6). See paragraph 4.0.
Note 7: The outputs of the data register are updated one clock cycle before the rising edge of EOC.
Note 8: Human body model, 100 pF discharged through a 1.5 kresistor.
www.national.com
4
Direct download click here
 

Share Link : National-Semiconductor
All Rights Reserved © datasheetbank.com 2014 - 2019 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]