datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

AD9020SE/883 View Datasheet(PDF) - Analog Devices

Part Name
Description
View to exact match
AD9020SE/883
ADI
Analog Devices ADI
AD9020SE/883 Datasheet PDF : 12 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
AD9020
Parameter (Conditions)
Temp
Test
Level
AD9020JE/JZ
Min Typ Max
AD9020KE/KZ
Min Typ Max
Units
DYNAMIC PERFORMANCE (continued)
Harmonic Distortion
fIN = 2.3 MHz
fIN = 10.3 MHz
fIN = 15.3 MHz
Two-Tone Intermodulation
+25°C I
+25°C I
+25°C I
Distortion Rejection7
+25°C V
Differential Phase
+25°C V
Differential Gain
+25°C V
61
67
55
59
49
53
70
0.5
1
61
67
55
59
49
53
70
0.5
1
dBc
dBc
dBc
dBc
Degree
%
ENCODE INPUT
Logic “1” Voltage
Logic “0” Voltage
Logic “1” Current
Logic “0” Current
Input Capacitance
Pulse Width (High)
Pulse Width (Low)
Full
VI
Full
VI
Full
VI
Full
VI
+25°C V
+25°C I
+25°C I
2.0
2.0
V
0.8
0.8
V
20
20
µA
800
800
µA
5
5
pF
6
6
ns
6
6
ns
DIGITAL OUTPUTS
Logic “1” Voltage (IOH = 2 mA) Full
VI
Logic “0” Voltage (IOL = 6 mA) Full
VI
POWER SUPPLY
+VS Supply Current
–VS Supply Current
Power Dissipation
+25°C I
Full
VI
+25°C I
Full
VI
+25°C I
Full
VI
Power Supply Rejection
Ratio (PSRR)8
Full
VI
2.4
0.4
440 530
542
140 170
177
2.8 3.3
3.4
6
10
2.4
440 530
542
140 170
177
2.8 3.3
3.4
6
10
V
V
mA
mA
mA
mA
W
W
mV/V
NOTES
1Absolute maximum ratings are limiting values to be applied individually, and beyond which the service ability of the circuit may be impaired. Functional operability is
not necessarily implied. Exposure to absolute maximum rating conditions for an extended period of time may affect device reliability.
2Typical thermal impedances (part soldered onto board): 68-pin leaded ceramic chip carrier: θJC = 1°C/W; θJA = 17°C/W (no air flow); θJA = 15°C/W
(air flow = 500 LFM). 68-pin ceramic LCC: θJC = 2.6°C/W; θJA = 15°C/W (no air flow); θJA = 13°C/W (air flow = 500 LFM).
33/4REF, 1/2REF, and 1/4REF reference ladder taps are driven from dc sources at +0.875 V, 0 V, and –0.875 V, respectively. Accuracy of the overflow comparator is not
tested and not included in linearity specifications.
4Measured with ANALOG IN = +VSENSE.
5Output delay measured as worst-case time from 50% point of the rising edge of ENCODE to 50% point of the slowest rising or falling edge of D 0–D9. Output skew
measured as worst-case difference in output delay among D0–D9.
6RMS signal to rms noise with analog input signal 1 dB below full scale at specified frequency.
7Intermodulation measured with analog input frequencies of 2.3 MHz and 3.0 MHz at 7 dB below full scale.
8Measured as the ratio of the worst-case change in transition voltage of a single comparator for a 5% change in +V S or –VS.
Specifications subject to change without notice.
REV. A
–3–
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]