AD8033/AD8034
SPECIFICATIONS (TA = 25؇C, VS = ؎12 V, RL = 1 k⍀, Gain = +2, unless otherwise noted.)
Parameter
Conditions
Min Typ
Max
DYNAMIC PERFORMANCE
–3 dB Bandwidth
Input Overdrive Recovery Time
Output Overdrive Recovery Time
Slew Rate (25% to 75%)
Settling Time to 0.1%
G = +1, VO = 0.2 V p-p
G = +2, VO = 0.2 V p-p
G = +2, VO = 2 V p-p
–13 V to +13 V Input
65
80
30
21
100
–6.5 V to +6.5 V Input, G = +2
100
G = +2, VO = 4 V Step
G = +2, VO = 2 V Step
G = +2, VO = 10 V Step
55
80
90
225
NOISE/HARMONIC PERFORMANCE
Distortion
fC = 1 MHz, VO = 2 V p-p
Second Harmonic
RL = 500 Ω
–80
RL = 1 kΩ
–82
Third Harmonic
RL = 500 Ω
–70
RL = 1 kΩ
–82
Crosstalk, Output to Output
f = 1 MHz, G = +2
–86
Input Voltage Noise
f = 100 kHz
11
Input Current Noise
f = 100 kHz
0.7
DC PERFORMANCE
Input Offset Voltage
Input Offset Voltage Match
Input Offset Voltage Drift
Input Bias Current
Open-Loop Gain
INPUT CHARACTERISTICS
Common-Mode Input Impedance
Differential Input Impedance
Input Common-Mode Voltage Range
FET Input Range
Usable Input Range
Common-Mode Rejection Ratio
OUTPUT CHARACTERISTICS
Output Voltage Swing
Output Short Circuit Current
Capacitive Load Drive
VCM = 0 V
TMIN – TMAX
TMIN – TMAX
VO = ± 8 V
VCM = ± 5 V
30% Overshoot; G = +1
1
2.0
3.5
2.5
4
24
2
12
50
88
96
1000||2.3
1000||1.7
–12.0 to +9.0
–12.0 to +12.0
–92
–100
± 11.52 ± 11.84
60
35
POWER SUPPLY
Operating Range
Quiescent Current per Amplifier
Power Supply Rejection Ratio
Specifications subject to change without notice.
VS = ± 2 V
5
24
3.3
3.5
–85
–100
Unit
MHz
MHz
MHz
ns
ns
V/µs
ns
ns
dBc
dBc
dBc
dBc
dB
nV/√Hz
fA/√Hz
mV
mV
mV
µV/oC
pA
pA
dB
GΩ||pF
GΩ||pF
V
V
dB
V
mA
pF
V
mA
dB
ABSOLUTE MAXIMUM RATINGS*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26.4 V
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . See Figure 2
Common-Mode Input Voltage . . . . . . . . . . . . . . . . . . . 26.4 V
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . 1.4 V
Storage Temperature . . . . . . . . . . . . . . . . . . –65°C to +125°C
Operating Temperature Range . . . . . . . . . . . –40°C to +85°C
Lead Temperature Range (Soldering 10 sec) . . . . . . . . . 300°C
*Stresses above those listed under Absolute Maximum Ratings may cause perma-
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
–4–
REV. B