datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

AD4016M181RTB-5 View Datasheet(PDF) - Unspecified

Part Name
Description
View to exact match
AD4016M181RTB-5 Datasheet PDF : 28 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
Notes :
1. AC measurements assume tT = 2ns.
2. An initial pause of 100 µs is required after power up, and it followed by a minimum of eight
initialization cycles (RAS - only refresh cycle or CAS - before - RAS refresh cycle). If the internal
refresh counter is used, a minimun of eight CAS - before - RAS refresh cycles are required.
3. In delayed write or read-modify-write cycles, OE must disable output buffer prior to applying data to
the device.
4. All the VCC and VSS pins shall be supplied with the same voltages.
5. tRAS(min) = tRWD(min)+tRWL(min)+tT in read-modify-write cycle.
6. tCAS(min) = tCWD(min)+tCWL(min)+tT in read-modify-write cycle.
7. tASC(min), tRCS(min), tWCS(min), and tRPC are determined by the falling edge of CAS .
8. tRCD(max) is specified as a reference point only, and tRAC(max) can be met with the tRCD(max) limit.
Otherwise, tRAC is controlled exclusively by tCAC if tRCD is greater than the specified tRCD(max) limit.
9. tRAD(max) is specified as a reference point only, and tRAC(max) can be met with the tRAD(max) limit.
Otherwise, tRAC is controlled exclusively by tAA if tRAD is greater than the specified tRAD(max) limit.
10. tCRP, tCHR, tRCH, tCPA and tCPW are determined by the rising edge of CAS .
11. VIH(min) and VIL(max) are reference levels for measuring timing or input signals. Therefore, transition
time is measured between VIH and VIL.
12. Assumes that tRCD tRCD(max) and tRAD tRAD(max). If tRCD or tRAD is greater than the maximum
recommended value shown in this table, tRAC exceeds the value shown.
13. Assumes that tRCD tRCD(max) and tRAD tRAD (max).
14. Access time is determined by the maximum of tAA, tCAC, tCPA.
15. Assumes that tRCD tRCD (max) and tRAD tRAD (max).
16. Either tRCH or tRRH must be satisfied for a read cycle.
17. tOFF(max) and tOEZ(max) define the time at which the output achieves the open circuit condition (high
impedance). tOFF is determined by the later rising edge of RAS or CAS.
18. tWCS, tRWD, tCWD, and tAWD are not restrictive operating parameters. They are included in the data
sheet as electrical characteristics only. If tWCS tWCS (min), the cycle is an early write cycle and the
data out will remain open circuit (high impedance) throughout the entire cycle. If tRWD tRWD (min),
tCWD tCWD (min), tAWD tAWD (min) and tCPW tCPW (min), the cycle is a read-modify-write and
the data output will contain data read from the selected cell. If neither of the above sets of conditions
is satisfied, the condition of the data output (at access time) is indeterminate.
19. These parameters are referenced to CAS separately in an early write cycle and to WE edge in a
delayed write or a read-modify-write cycle.
20. tRASP defines RAS pulse width in EDO page mode cycles.
Rev.1
Page 14
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]