datasheetbank_Logo     Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

4066-D14-R View Datasheet(PDF) - Unisonic Technologies

Part NameDescriptionManufacturer
4066-D14-R QUAD BILATERAL SWITCH UTC
Unisonic Technologies UTC
4066-D14-R Datasheet PDF : 7 Pages
1 2 3 4 5 6 7
4066
CMOS IC
AC ELECTRICAL CHARACTERISTICS (AC Parameters are guaranteed by DC correlated testing)
(Ta=25, tr=tf=20 ns and Vss=0V unless otherwise)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX UNITS
Propagation Delay Time Signal
Input to Signal Output
TPHL, TPLH
Vc=VDD, CL=50pF, (Figure1)
RL=200k
VDD=5V
VDD=10V
VDD=15V
25 55 ns
15 35 ns
10 25 ns
Propagation Delay Time
Control Input to Signal
Output High Impedance to
Logical Level
RL=1.0k, CL=50pF
tPZH, tPLZ (Figure 2, Figure3)
VDD=5V
VDD=10V
VDD=15V
125 ns
60 ns
50 ns
Propagation Delay Time
Control Input to Signal
Output Logical Level to
High Impedance
Sine Wave Distortion
Frequency Response -Switch
“ON” (Frequency at-3dB)
tPHZ, tPLZ
RL=1.0k, CL=50pF, (Figure 2, Figure3)
VDD=5V
VDD=10V
VDD=15V
Vc=VDD=5V, Vss= -5V
RL=10k, VIS=5VP-P, f=1kHz, (Figure 4)
Vc=VDD=5V, Vss= -5V
RL=1k, VIS=5Vp-p
20 Log10 VOS/VOS (1kHz)-dB
(Figure 4)
125 ns
60 ns
50 ns
0.1
%
40
MHz
Feedthrough - Switch “OFF”
(Frequency at –50 dB)
Crosstalk Between Any Two
Switches(Frequency at-50dB)
Crosstalk; Control Input to
Signal Output
VDD=5.0V, Vcc=Vss= -5.0V,
RL=1k, VIS=5.0VP-P, 20Log10,
VOS/VIS= -50dB, (Figure 4)
VDD=VC(A)=5.0V; Vss=Vc (B)=5.0V,
RL=1k, VIS(A)=5.0VP-P, 20Log10,
VOS(B)/VIS (A)= -50dB (Figure 5)
VDD=10V, RL=10k, RIN=1.0k
Vcc=10V Square Wave, CL=50pF
(Figure 6)
1.25
0.9
150
MHz
mVp-p
Maximum Control Input
RL=1.0k, CL=50pF, (Figure 7)
Vos (f) =1/2Vos (1.0kHz)
Signal Input Capacitance
VDD=5.0V
VDD=10V
VDD=15V
CIS
6.0
MHz
8.0
MHz
8.5
MHz
8.0
pF
Signal Output Capacitance
COS
VDD=10V
8.0
pF
Feedthrough Capacitance
CIOS VC=0V
0.5
pF
Control lnput Capacitance
CIN
5.0 7.5 pF
Note 1: These devices should not be connected to circuits with the power ”ON”
Note 2: In all cases, these is approximately 5pF of probe and jig capacitance in the output; however, this capacitance
is included in CL wherever it is specified.
Note 3: VIS is the voltage at the in/out pin and VOS is the voltage at the out/in pin. Vc is the voltage at the control
input.
Note 4: Conditions for VIHC: (a) VIS=VDD, Ios=standard B series IOH. (b) VIS=0V, IOL=standard B series IOL
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 7
QW-R502-009,C
Direct download click here

 

Share Link : 

All Rights Reserved © datasheetbank.com 2014 - 2020 [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]