FIN1022MTCX View Datasheet(PDF) - Fairchild Semiconductor
Part Name
Description
View to exact match
FIN1022MTCX Datasheet PDF : 10 Pages
| |||
Absolute Maximum Ratings(Note 1)
Supply Voltage (VCC)
DC Input Voltage (VIN)
DC Output Voltage (VOUT)
Driver Short Circuit Current (IOSD)
Storage Temperature Range (TSTG)
Max Junction Temperature (TJ)
Lead Temperature (TL)
(Soldering, 10 seconds)
−0.3V to +4.6V
−0.3V to +4.6V
−0.3V to +4.6V
Continuous
−65°C to +150°C
150°C
260°C
Recommended Operating
Conditions
Supply Voltage (VCC)
Input Voltage (VIN)
Operating Temperature (TA)
Electrostatic Discharge
3.0V to 3.6V
0 to VCC
−40°C to +85°C
(HBM 1.5 kΩ, 100 pF)
>7500V
Electrostatic Discharge
(MM 0Ω, 100 pF)
>300V
Note 1: The “Absolute Maximum Ratings”: are those values beyond which
damage to the device may occur. The databook specifications should be
met, without exception, to ensure that the system design is reliable over its
power supply, temperature and output/input loading variables. Fairchild
does not recommend operation of circuits outside databook specification.
DC Electrical Characteristics
Over supply voltage and operating temperature ranges, unless otherwise specified (Note 2)
Symbol
Parameter
Min
Test Conditions
LVDS Differential Driver Characteristics
VOD
Output Differential Voltage
RL = 75 Ω, See Figure 3
270
RL = 75 Ω, See Figure 3
285
TA = 25°C and VCC = 3.3V
∆VOD
VOD Magnitude Change from
Differential LOW-to-HIGH
RL = 75 Ω, See Figure 3
VOS
Offset Voltage
See Figure 3
1.0
∆VOS
Offset Magnitude Change from
Differential LOW-to-HIGH
See Figure 3
IOZD
IOFF
IOS
Disabled Output Leakage Current
Power-Off Current
Short Circuit Output Current
LVDS Differential Receiver Characteristics
VOUT = 3.6V or GND, Driver Disabled
VCC = 0V, VIN or VOUT = 3.6V or 0V
VOUT = 0V, Driver Enabled
VOUTx+ = 0V, VOUTx− = 0V, Driver Enabled
VTH
Differential Input Threshold HIGH
VTL
Differential Input Threshold LOW
VIC
Input Common Mode Voltage
IIND
Input Current (Differential Inputs)
LVTTL Control Characteristics
VIC = 0.05V or 1.2V or 3.25V
VCC = 3.3V
VIN = GND
VIN = VCC
−100
0.05
VIH
Input High Voltage
2
VIL
Input Low Voltage
IIN
Input Current
VIN = 3.6V or GND
Device Characteristics
VIK
Input Clamp Voltage
IIK = −18 mA
−1.5
IPU/PD
Output Power-Up/Power-Down
High Z Leakage Current
VCC = 0V to 1.5V
CIN
Input Capacitance
COUT
Output Capacitance
ICC
Power Supply Current
No Load, All Drivers Enabled
RL = 75 Ω, All Drivers Enabled
RL = 75 Ω, All Drivers Enabled
Note 2: This part will only function with datasheet specification when a resistive load is applied to the driver outputs.
Note 3: All typical values are at TA = 25°C and with VCC = 3.3V.
Typ
(Note 3)
365
365
1.2
4.5
4.5
Max
475
440
35
1.45
35
±10
±20
−10
−10
100
3.25
±20
±20
0.8
±20
±10
35
35
35
Units
mV
mV
V
mV
µA
µA
mA
mV
V
µA
V
V
µA
V
µA
pF
pF
mA
mA
mA
3
www.fairchildsemi.com
|
|
Share Link: 