datasheetbank_Logo    Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site
Part Name :

TDA2030A View Datasheet(PDF) - STMicroelectronics

Part NameTDA2030A ST-Microelectronics
STMicroelectronics ST-Microelectronics
Description18W Hi-Fi AMPLIFIER AND 35W DRIVER
TDA2030A Datasheet PDF : 16 Pages
1 2 3 4 5 6 7 8 9 10 Next Last
TDA2030A
Figure 18 : Power Distribution versus Frequency
A more effective solution, named "Active Power
Filter" by SGS-THOMSON is shown in Figure 19.
Figure 19 : Active Power Filter
Both active and passive filters can be used for
crossovers but today active filters cost significantly
less than a good passive filter using air cored
inductors and non-electrolytic capacitors. In addi-
tion, active filters do not suffer from the typical
defects of passive filters:
- power less
- increased impedance seen by the loudspeaker
(lower damping)
- difficulty of precise design due to variable loud-
speaker impedance.
Obviously, active crossovers can only be used if a
power amplifier is provided for each drive unit. This
makes it particularly interesting and economically
sound to use monolithic power amplifiers.
In some applications, complex filters are not really
necessary and simple RC low-pass and high-pass
networks (6dB/octave) can be recommended.
The result obtained are excellent because this is
the best type of audio filter and the only one free
from phase and transient distortion.
The rather poor out of band attenuation of single
RC filters means that the loudspeaker must operate
linearly well beyond the crossover frequency to
avoid distortion.
The proposed circuit can realize combined power
amplifiers and 12dB/octave or 18dB/octave high-
pass or low-pass filters.
In practice, at the input pins of the amplifier two
equal and in-phase voltages are available, as re-
quired for the active filter operation.
The impedance at the pin (-) is of the order of 100,
while that of the pin (+) is very high, which is also
what was wanted.
The component values calculated for fc = 900Hz
using a Bessek 3rd order Sallen and Key structure
are :
C1 = C2 = C3
22nF
R1
8.2k
R2
5.6k
R3
33k
Using this type of crossover filter, a complete 3-way
60W active loudspeaker system is shown in Fig-
ure 20.
It employs 2nd order Buttherworth filters with the
crossover frequencies equal to 300Hz and 3kHz.
The midrange section consists of two filters, a high
pass circuit followed by a low pass network. With
VS = 36V the output power delivered to the woofer
is 25W at d = 0.06% (30W at d = 0.5%).
The power delivered to the midrange and the
tweeter can be optimized in the design phase
taking in account the loudspeaker efficiency and
impedance (RL = 4to 8).
It is quite common that midrange and tweeter
speakers have an efficiency 3dB higher than-
woofers.
9/15
Direct download click here
 

DESCRIPTION
The TDA2030A is a monolithic IC in Pentawatt ® package intended for use as low frequency class AB amplifier.
With VS max = 44V it is particularly suited for more reliable applications without regulated supply and for 35W driver circuits using low-cost complementary pairs. The TDA2030A provides high output current and has very low harmonic and cross-over distortion. Further the device incorporates a short circuit protection system comprising an arrangement for automatically limiting the dissipated power so as to keep the working point of the output transistors within their safe operating area. A conventional thermal shut-down system is also included.

Share Link : ST-Microelectronics
@ 2014 - 2018  [ Home ] [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]