datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

ADR425 View Datasheet(PDF) - Analog Devices

Part Name
Description
View to exact match
ADR425 Datasheet PDF : 24 Pages
First Prev 11 12 13 14 15 16 17 18 19 20 Next Last
ADR420/ADR421/ADR423/ADR425
APPLICATIONS
OUTPUT ADJUSTMENT
The ADR42x trim terminal can be used to adjust the output
voltage over a ±0.5% range. This feature allows the system
designer to trim system errors out by setting the reference to
a voltage other than the nominal. This is also helpful if the
part is used in a system at temperature to trim out any error.
Adjustment of the output has a negligible effect on the
temperature performance of the device. To avoid degrading
temperature coefficients, both the trimming potentiometer
and the two resistors need to be low temperature coefficient
types, preferably <100 ppm/°C.
INPUT
2
VIN VOUT 6
ADR420/
ADR421/
ADR423/
ADR425
GND TRIM 5
4
OUTPUT
VOUT = ±0.5%
R1
470k
RP
10k
R2 10k(ADR420)
15k(ADR421)
Figure 40. Output Trim Adjustment
REFERENCE FOR CONVERTERS IN OPTICAL
NETWORK CONTROL CIRCUITS
In the high capacity, all optical router network of Figure 41,
arrays of micromirrors direct and route optical signals from
fiber to fiber, without first converting them to electrical form,
which reduces the communication speed. The tiny micro-
mechanical mirrors are positioned so that each is illuminated
by a single wavelength that carries unique information and
can be passed to any desired input and output fiber. The mirrors
are tilted by the dual-axis actuators controlled by precision
analog-to-digital converters (ADCs) and digital-to-analog
converters (DACs) within the system. Due to the microscopic
movement of the mirrors, not only is the precision of the
converters important, but the noise associated with these
controlling converters is extremely critical, because total noise
within the system can be multiplied by the numbers of
converters used. Consequently, the exceptional low noise of the
ADR42x is necessary to maintain the stability of the control
loop for this application.
SOURCE FIBER
GIMBAL + SENSOR
LASER BEAM
ACTIVATOR
LEFT
MEMS MIRROR
DESTINATION
FIBER
ACTIVATOR
RIGHT
AMPL
PREAMP
AMPL
CONTROL
ELECTRONICS
DAC
ADC
DAC
ADR421
ADR421
ADR421
DSP
Figure 41. All Optical Router Network
A NEGATIVE PRECISION REFERENCE
WITHOUT PRECISION RESISTORS
In many current-output CMOS DAC applications where
the output signal voltage must be of the same polarity as the
reference voltage, a current-switching DAC is often recon-
figured into a voltage-switching DAC with a 1.25 V reference,
an op amp, a pair of resistors, and an additional operational
amplifier at the output to reinvert the signal. A negative voltage
reference should be used because an additional operational
amplifier is not required for either reinversion (current-switching
mode) or amplification (voltage-switching mode) of the DAC
output voltage. In general, any positive voltage reference can be
converted into a negative voltage reference using an operational
amplifier and a pair of matched resistors in an inverting
configuration. The disadvantage to this approach is that the
largest single source of error in the circuit is the relative
matching of the resistors used.
A negative reference can easily be generated by adding a
precision op amp and configuring as shown in Figure 42. VOUT
is at virtual ground and, therefore, the negative reference can be
taken directly from the output of the op amp. The op amp must
be dual-supply, low offset and have rail-to-rail capability if
negative supply voltage is close to the reference output.
+VDD
2
VIN
ADR420/
ADR421/
ADR423/
ADR425
6 VOUT
GND
4
A1
–VREF
A1 = OP777, OP193
–VDD
Figure 42. Negative Reference
Rev. H | Page 17 of 24
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]