 전자부품 반도체 검색엔진( 무료 PDF 다운로드 ) - 데이터시트뱅크

# ADR423BRZ-RevI 데이터 시트보기 (PDF) - Analog Devices

 부품명 상세내역 제조사 ADR423BRZ(RevI) Ultraprecision, Low Noise, 2.048 V/2.500 V/3.00 V/5.00 V XFET� Voltage References Analog Devices ADR423BRZ Datasheet PDF : 24 Pages
 First Prev 11 12 13 14 15 16 17 18 19 20 Next Last TERMINOLOGY
Temperature Coefficient
The change of output voltage over the operating temperature
range is normalized by the output voltage at 25°C, and
expressed in ppm/°C as
TCVOUT
(ppm / °C)
=
( ) VOUT T2 VOUT
VOUT (25°C) × (T2
(T1 )
T1 )
×
106
where:
VOUT (25°C) = VOUT at 25°C.
VOUT (T1) = VOUT at Temperature 1.
VOUT (T2) = VOUT at Temperature 2.
Line Regulation
The change in output voltage due to a specified change in input
voltage. It includes the effects of self-heating. Line regulation is
expressed in either percent per volt, parts per million per volt,
or microvolts per volt change in input voltage.
The change in output voltage due to a specified change in load
current. It includes the effects of self-heating. Load regulation is
expressed in either microvolts per milliampere, parts per
million per milliampere, or ohms of dc output resistance.
Long-Term Stability
Typical shift of output voltage at 25°C on a sample of parts
subjected to operation life test of 1000 hours at 125°C.
( ) ( ) ΔVOUT = VOUT t 0 VOUT t1
ΔVOUT (ppm)
=
( ) ( ) VOUT t 0 VOUT t1 × 106
( ) VOUT t 0
where:
VOUT (t0) = VOUT at 25°C at Time 0.
VOUT (t1) = VOUT at 25°C after 1000 hours operation at 125°C.
Thermal Hysteresis
The change of output voltage after the device is cycled through
temperatures from +25°C to −40°C to +125°C and back to
+25°C. This is a typical value from a sample of parts put
through such a cycle.
VOUT _ HYS = VOUT (25°C) VOUT _ TC
( ) VOUT _ HYS
ppm
= VOUT (25°C ) VOUT _ TC
VOUT (25°C)
× 106
where:
VOUT (25°C) = VOUT at 25°C.
VOUT_TC = VOUT at 25 °C after temperature cycle at +25°C to
−40°C to +125°C and back to +25°C.
Input Capacitor
Input capacitors are not required on the ADR42x. There is
no limit for the value of the capacitor used on the input, but a
1 μF to 10 μF capacitor on the input improves transient response
in applications where the supply suddenly changes. An addi-
tional 0.1 μF capacitor in parallel also helps to reduce noise
from the supply.
Output Capacitor
The ADR42x do not need output capacitors for stability under
any load condition. An output capacitor, typically 0.1 μF, filters
out any low level noise voltage and does not affect the operation
of the part. On the other hand, the load transient response can
be improved with an additional 1 μF to 10 μF output capacitor
in parallel. A capacitor here acts as a source of stored energy for
sudden increase in load current. The only parameter that