datasheetbank_Logo
Integrated circuits, Transistor, Semiconductors Search and Datasheet PDF Download Site

IMP708TCSA View Datasheet(PDF) - A1 PROs co., Ltd.

Part Name
Description
View to exact match
IMP708TCSA
A1PROS
A1 PROs co., Ltd. A1PROS
IMP708TCSA Datasheet PDF : 9 Pages
1 2 3 4 5 6 7 8 9
IMP706P/R/S/T/J, IMP708R/S/T/J
Detail Descriptions
RESET/RESET Operation
The RESET/RESET signals are designed to start or return a
µP/µC to a known state.
With VCC above 1.2V, RESET and RESET are guaranteed to be
asserted. During a power-up sequence, the reset outputs remain
asserted until the supply rises above the threshold level. The
resets are deasserted approximately 200ms after crossing the
threshold.
In a brownout situation where VCC falls below the threshold level,
the reset outputs are asserted. If a brownout occurs during an
already initiated reset period, the reset period will extend for an
additional reset period of 200ms.
The IMP708 devices have dual reset outputs, one active LOW and
one active HIGH. The IMP706P has a single active HIGH reset and
the IMP706/R/S/T/J devices have an active LOW reset output.
IMP Part
IMP706P
IMP706R
IMP706S
IMP706T
IMP706J
IMP708R
IMP708S
IMP708T
IMP708J
RESET Polarity
HIGH
LOW
LOW
LOW
LOW
Both: HIGH & LOW
Both: HIGH & LOW
Both: HIGH & LOW
Both: HIGH & LOW
Threshold Watchdog Timer
2.63V
Yes
2.63V
Yes
2.93V
Yes
3.08V
Yes
4.00V
Yes
2.63V
No
2.93V
No
3.08V
No
4.00V
No
Manual Reset (MR)
The active-LOW manual reset input is pulled high by an internal
20kpull-up resistor and can be driven low by CMOS/TTL logic
or a mechanical switch to ground. An external debounce circuit is
unnecessary since the 140ms minimum reset time will debounce
mechanical pushbutton switches. The minimum MR input pulse
width is 0.5µs with a 3V VCC input and 0.15µs with a 5V VCC
input. If not used, tie MR to VCC or leave floating.
By connecting the watchdog output (WDO) and MR, a watchdog
timeout forces a RESET to be generated.
Watchdog Timer
A watchdog timer available on the IMP706P/R/S/T/J monitors
µP/µC activity. If activity is not detected within 1.6 seconds on the
Watchdog Input (WDI), the internal timer puts the Watchdog
Output (WDO) into a LOW state. WDO will remain LOW until
activity is detected at WDI.
The watchdog function is disabled, meaning it is cleared and not
counting, if WDI is floated or connected to a three-stated circuit.
The watchdog timer is also disabled if RESET is asserted. When
RESET becomes inactive and the WDI input sees a high or low
transition as short as 100ns (VCC = 2.7V)/50ns (VCC = 4.5V), the
watchdog timer will begin a 1.6 second countdown. Additional
transitions at WDI will reset the watchdog timer and initiate a
new countdown sequence.
WDO will also become LOW and remain so, whenever the supply
voltage, VCC, falls below the device threshold level. WDO goes HIGH
as soon as VCC transitions above the threshold. There is no minimum
pulse width for WDO as there is for the RESET outputs. If WDI is float-
ed, WDO essentially acts as a low supply voltage output indicator.
Power-failure detection with auxiliary comparator
All devices have an auxiliary comparator with 1.25V trip point.
The output, PFO, is active LOW and the noninverting input is PFI.
This comparator can be used as a supply voltage monitor with an
external resistor voltage divider. As the monitored voltage level
falls, PFI is reduced causing the PFO output to go LOW.
Normally PFO interrupts the processor so the system can be shut
down in a controlled manner.
5V
VCC
vRT
0V
tRS
tRS
5V
WDI
0V
tWP
5V
WDO
0V
5V
RESET
0V
6
tWD
tWD
5V
RESET
0V
5V
MR
0V
tWD
RESET triggered by MR
Watchdog Timing
706P_04.eps
5V
WDO
0V
408-432-9100/www.impweb.com
MR externally
set low
tMD
tMR
WDI Three-state operation
706P_05.eps
© 1999 IMP, Inc.
 

Share Link: 

datasheetbank.com [ Privacy Policy ] [ Request Datasheet ] [ Contact Us ]