CAT24WC256J-3TE13 View Datasheet(PDF) - Catalyst Semiconductor => Onsemi
Part Name
Description
View to exact match
CAT24WC256J-3TE13 Datasheet PDF : 10 Pages
| |||
CAT24WC256
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground(1) ........... –2.0V to +VCC + 2.0V
VCC with Respect to Ground ............... –2.0V to +7.0V
Package Power Dissipation
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current(2) ........................ 100mA
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of
the device at these or any other conditions outside of those
listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for
extended periods may affect device performance and
reliability.
RELIABILITY CHARACTERISTICS
Symbol
Parameter
Reference Test Method
Min
NEND(3)
TDR(3)
VZAP(3)
ILTH(3)(4)
Endurance
Data Retention
ESD Susceptibility
Latch-up
MIL-STD-883, Test Method 1033 100,000
MIL-STD-883, Test Method 1008 100
MIL-STD-883, Test Method 3015 2000
JEDEC Standard 17
100
D.C. OPERATING CHARACTERISTICS
VCC = +1.8V to +6.0V, unless otherwise specified.
Symbol Parameter
Test Conditions Min
ICC1
ICC2
ISB(5)
ILI
ILO
VIL
VIH
VOL1
VOL2
Power Supply Current - Read
Power Supply Current - Write
Standby Current
Input Leakage Current
Output Leakage Current
Input Low Voltage
fSCL = 100 KHz
VCC=5V
fSCL = 100KHz
VCC=5V
VIN = GND or VCC
VCC=5V
VIN = GND to VCC
VOUT = GND to VCC
–1
Input High Voltage
Output Low Voltage (VCC = +3.0V)
Output Low Voltage (VCC = +1.8V)
IOL = 3.0 mA
IOL = 1.5 mA
VCC x 0.7
Typ
Typ
Max
Units
Cycles/Byte
Years
Volts
mA
Max Units
1
mA
3
mA
1
µA
1
µA
1
µA
VCC x 0.3 V
VCC + 0.5 V
0.4
V
0.5
V
CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V
Symbol Test
Conditions Min
Typ
CI/O(3) Input/Output Capacitance (SDA)
VI/O = 0V
CIN(3)
Input Capacitance (SCL, WP, A0, A1) VIN = 0V
Max
Units
8
pF
6
pF
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is VCC +0.5V, which may overshoot to VCC + 2.0V for periods of less than 20ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to VCC +1V.
(5) Maximum standby current (ISB ) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1031, Rev. F
2
|
|
Share Link: 