MAX4558CEE View Datasheet(PDF) - Maxim Integrated
Part Name
Description
View to exact match
MAX4558CEE Datasheet PDF : 16 Pages
| |||
±15kV ESD-Protected, Low-Voltage, CMOS
Analog Multiplexers/Switches
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to VEE)
VCC ........................................................................ -0.3V to +13V
Voltage into Any Terminal (Note 1).... (VEE - 0.3V) to (VCC + 0.3V)
Continuous Current into Any Terminal .............................±10mA
Peak Current, X, Y, Z, X_, Y_, Z_
(pulsed at 1ms, 10% duty cycle) ..................................±30mA
ESD per Method IEC 1000-4-2 (X, Y, Z, X_, Y_, Z_)
Air-Gap Discharge ......................................................... ±12kV
Contact Discharge ............................................................±8kV
ESD per Method 3015.7
VCC, VEE, A, B, C, ENABLE, GND ................................ ±2.5kV
X, Y, Z, X_, Y_, Z_............................................................±15kV
Continuous Power Dissipation (TA = +70°C)
QSOP (derate 8.00mW/°C above +70°C) .................... 640mW
Narrow SO (derate 8.70mW/°C above +70°C) .............696mW
DIP (derate 10.53mW/°C above +70°C) .......................842mW
Operating Temperature Ranges
MAX45_ _C_E ......................................................0°C to +70°C
MAX45_ _E_E ...................................................-40°C to +85°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Signals on any terminal exceeding VCC or VEE are clamped by internal diodes. Limit forward diode current to maximum cur-
rent rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Dual ±5V Supplies
(VCC = +4.5V to +5.5V, VEE = -4.5V to -5.5V, V_H = +2.4V, V_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values
are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
TA
MIN TYP MAX
(Note 2)
UNITS
ANALOG SWITCH
Analog Signal Range
VX_, VY_,
VZ_, VX,
VY, VZ
C, E
V-
V+
V
On-Resistance
RON
VCC = 4.5V; VEE = -4.5V;
IX, IY, IZ = 1mA; VX_, VY_, VZ_ = ±3V
+25°C
C, E
110 160
Ω
180
On-Resistance Match
Between Channels (Note 3)
∆RON
VCC = 4.5V; VEE = -4.5V;
IX, IY, IZ = 1mA; VX_, VY_, VZ_ = ±3V
+25°C
C, E
2
6
Ω
8
On-Resistance Flatness
(Note 4)
RFLAT(ON)
VCC = 4.5V; VEE = -4.5V;
IX, IY, IZ = 1mA; VX_, VY_, VZ_ = -3V, 0V, 3V
+25°C
C, E
3
8
Ω
10
X_, Y_ , Z_ Off-Leakage
Current (Note 5)
IX_(OFF),
IY_(OFF),
IZ_(OFF)
VCC = 5.5V; VEE = -5.5V;
VX_, VY_, VZ_ = 4.5V, -4.5V;
VX, VY, VZ = -4.5V, 4.5V
+25°C -1 0.002 1
nA
C, E -10
10
+25°C -2 0.002 2
X, Y, Z Off-Leakage Current
(Note 5)
IX(OFF),
IY(OFF),
IZ(OFF)
VCC = 5.5V; VEE = -5.5V;
VX_, VY_, VZ_ = 4.5V, -4.5V;
VX, VY, VZ = -4.5V, 4.5V
MAX4558
MAX4559
C, E -20
20
+25°C -1 0.002 1
nA
MAX4560
C, E -10 0.002 10
+25°C -2 0.002 2
X, Y, Z On-Leakage Current
(Note 5)
IX(ON),
IY(ON),
IZ(ON)
VCC = 5.5V; VEE = -5.5V;
VX_, VY_, VZ_ = 4.5V, 4.5V;
VX, VY, VZ = 4.5V, -4.5V
MAX4558
MAX4559
C, E
+25°C
-20
20
-1 0.002 1
nA
MAX4560
C, E -10 0.002 10
2 _______________________________________________________________________________________
|
|
Share Link: 